5/8 inch SS201 welded wire mesh is a grid made by welding stainless steel wires at their intersections, with “5/8 inch” usually referring to the nominal clear opening. That opening converts to 15.875 mm, but the opening size alone does not define a complete product specification. Buyers should also confirm wire diameter, mesh dimensions, tolerances, finish, and whether the stated opening is measured as a clear gap or a wire-center spacing. At Shunqiang Wire Mesh, we recommend confirming these details before comparing quotations or approving a sample.
If you are looking for more details, kindly visit our website.
This guide is for importers, fabricators, distributors, and project buyers evaluating 5/8 inch SS201 welded wire mesh. It is also useful for engineers who need to translate a general mesh description into a purchase-ready specification. The guidance explains the main variables to confirm and how to match the material to an application. It does not replace project-specific design review or material verification.
In a mesh description, “5/8 inch” commonly identifies the nominal opening between adjacent wires, but suppliers may use different conventions. A clear opening is the unobstructed distance between the inside edges of two wires, while pitch is the distance from the center of one wire to the center of the next. These measurements are not interchangeable, so the purchase specification should state which one is required. For metric coordination, 5/8 inch equals 15.875 mm.
Wire diameter also affects the grid’s pitch and open area. For example, if 15.875 mm is the clear opening, a 1.0 mm wire would give an illustrative center-to-center pitch of 16.875 mm, while a 1.5 mm wire would give 17.375 mm. These calculations explain the relationship between dimensions; they are not a claim that either diameter is a standard Shunqiang product option. Always request the actual production specification for the mesh being quoted.
SS201 refers to a grade in the 201 family of austenitic stainless steels. Its alloy balance differs from grades such as 304, and the choice should be based on the service environment rather than the word “stainless” alone. Corrosion performance can vary with exposure to moisture, salts, chemicals, temperature, surface condition, and cleaning practices. Where the mesh will face persistent dampness, chlorides, or corrosive chemicals, ask for a suitability review and consider whether another grade is more appropriate.
A complete inquiry should describe the mesh geometry, material, format, and intended use. The table below provides a practical checklist, rather than a fixed product datasheet. Values such as wire diameter and panel size must be agreed with the supplier because they are not determined by the 5/8 inch opening. Include tolerances and inspection expectations where these matter to assembly or downstream fabrication.
| Specification | What to Clarify | Why It Matters |
|---|---|---|
| Opening | 5/8 inch nominal; clear opening or center-to-center pitch; tolerance | Defines the grid and helps confirm fit with connected parts or screening needs. |
| Wire diameter | Required diameter and allowable variation | Influences rigidity, weight, open area, and fabrication compatibility. |
| Material | SS201 grade identification and any documentation required | Supports material traceability and helps evaluate environmental suitability. |
| Product format | Roll or panel, width, length, edge condition, and quantity | Determines how the mesh will be handled, cut, packed, and installed. |
| Finish and fabrication | Surface condition, cut edges, bends, frames, or other processing | Helps align the supplied product with the next manufacturing or installation step. |
Welded wire mesh is used where a regular, joined wire grid is needed for separation, guarding, support, or fabrication. A 5/8 inch opening may be considered for general enclosures, partitions, protective guards, equipment panels, or custom-fabricated components. Whether it is suitable depends on the required opening, wire diameter, load, support spacing, and applicable safety requirements. A mesh opening by itself does not establish a product’s load capacity or compliance with a particular design standard.
Link to Shunqiang Wire Mesh
For indoor applications with controlled exposure, SS201 may be a practical material candidate when the project requirements and cost targets align. For outdoor installations or locations exposed to salt, cleaning chemicals, or frequent wetting, assess corrosion risk before ordering. If appearance and long-term surface condition are important, request material details and, where appropriate, a sample for evaluation in the intended environment. Do not assume that two products with the same opening and wire diameter will perform identically if their material grade or surface condition differs.
Consider how the mesh will be supported and whether it must resist impact, pressure, vibration, or handling loads. Heavier wire or closer support spacing may be needed for some designs, but the correct solution depends on the application and should be reviewed by the responsible engineer. For fabrication, confirm whether the mesh will be cut, bent, welded to a frame, or assembled with other components. These operations can affect edge condition, dimensions, and the final fit.
When asking for a quotation, send a written specification rather than relying only on a product name. Include the required quantity, delivery destination, packaging needs, target schedule, and any documentation requirements. If your drawing uses metric dimensions, state whether those dimensions are nominal or subject to a specified tolerance. A clear inquiry helps suppliers identify unanswered questions before production planning begins.
Price depends on the agreed material, wire diameter, opening, product dimensions, quantity, processing, packaging, and delivery terms. Minimum order quantities and lead times can vary with the requested format, production schedule, and customization, so they should be confirmed for each inquiry. A lower unit price may not represent the best overall option if the mesh requires additional cutting, rework, or special handling after arrival. Compare quotations against the same specification and delivery basis.
Ask the supplier to confirm the opening definition, wire diameter, grade, tolerances, and supplied format in writing. Find out what inspection or material documentation can be provided for the specific order, rather than assuming that a generic product description guarantees traceability. If the mesh is being integrated into a finished assembly, ask how dimensions and edge conditions will be controlled. Requesting a pre-production sample or drawing review can help catch specification misunderstandings early.
At Shunqiang Wire Mesh, we work with buyers to clarify welded wire mesh requirements, including opening, wire diameter, grade, dimensions, and supply format. We can review your drawings or written specification and discuss whether the requested SS201 mesh configuration can be quoted for your project. Availability, customization, documentation, minimum order quantity, and lead time should be confirmed against the details of each order. Providing a complete inquiry helps us respond with a more relevant product proposal.
5/8 inch SS201 welded wire mesh is a welded stainless grid commonly specified by its nominal opening, but the opening alone is not enough to select or purchase the right product. Confirm that the 5/8 inch dimension means a clear opening or pitch, then define wire diameter, grade, tolerances, dimensions, finish, and format. Match SS201 to the real exposure conditions and review mechanical or safety requirements with the responsible project professional. To take the next step, send Shunqiang Wire Mesh your drawing or specification, intended application, quantity, and destination for a project-specific quotation.
Are you interested in learning more about 5/8 inch ss201 welded wire mesh? Contact us today to secure an expert consultation!